Differences

This shows you the differences between two versions of the page.

--- mcmaster:k2scope_archive [2016/07/12 03:46] – mcmaster
+++ mcmaster:k2scope_archive [2018/12/26 14:30] (current) – removed mcmaster
@@ Line 1: / Line 1: @@
-====== Nikon K2 IND ======
-{{:mcmaster:tech_inst:k2_ind:nikon_k2_ebay_01.jpg?300|}}
-{{:mcmaster:tech_inst:k2_ind:nikon_k2_ebay_05.jpg?300|}}
-Above: photo from eBay listing
-mm optics
-Came mostly complete save objectives.  Got a Nikon BD Plan 20x objective off of eBay but unfortunately its scratched a little :(.  Might not hurt image quality too much though.
-====== Zygo KMS310RT ======
-{{:mcmaster:tech_inst:k2_ind:disp_serv_k2_front.jpg?300|}}
-{{:mcmaster:tech_inst:k2_ind:disp_serv_k2_back.jpg?300|}}
-Above: system at auction.  Trivia: the CRT said Micron Technology on it...must have come from them
-Intended to be a mask aligner.  Infinity system.  I believe this is sold by Zygo with major components from Technical Instruments and Nikon.
-Very heavy!  Estimate 700 lbs
-Came as a complete system minus control system:
-  * Mercury burner w/ PS
-  * Fiber illuminator w/ PS
-  * Nikon CF Plan objectives (4).  Something like  %<nowiki> *</nowiki> 5x
-    * 10x
-    * 20x
-    * 100x
-  * TMC pneumatic anti-vibration table
-  * Motorized servo XY table
-  * Motorized Z axis (course focus)
-  * Piezo Z axis (fine focus)
-This page is about piecing it together to try to get it working again
-It came with a very small subsection of the user man.  I was able to contact Zygo and get some more info
-===== Chasis =====
-Dataplate:
-<code>
-Technical Instrument Company
-North Mary Avenue
-Sunyvale, CA 94086-2906
-Model: KMS310RT
-Serial No: XXX
-Assembly No: 015-00007-AA
-Manufacturered: TIC
-THIS PRODUCT CONFORMS TO 21 CFR
-AT DATE OF MANUFACTURE
-</code>
-===== K2 IND =====
-[[KMS310RT|Detailed teardown]]
-TMS300 or something
-Had a neutral density filter rattling around when I got it.  Have not looked to see where it came from.  Have not tried spinning it up
-Mercury burner: HB-10103AF
-<code>
-Technical Instrument Company
-North Mary Avenue
-Sunnyvale, CA 94086-2906
-Model: K2IND-KMS310
-Serial No: 9635-3235
-Assembly No: 200-00013-AJ
-Manufactured: August 1996
-</code>
-===== Piezo Z axis =====
-{{:mcmaster:tech_inst:k2_ind:pi_top.jpg?300|}}
-{{:mcmaster:tech_inst:k2_ind:pi_bot.jpg?300|}}
-Removed, but would be nice to get it working at some point
-PHYSIK INSTRUMENTE (PI)
-Type: P-960.00 Polarity: +
-Serial-No. XXX
-===== XY servo motor stage =====
-DC servo system with glass linear encoders.  Switched out for stepper system for quicker bring up but might eventually put it back on
-Motor: voltage/current/inductance?
-<code>
-QUALITY MOTION CONTROL
-PART NO. 2241-M2608
-SERIAL NO. 177
-DATE CODE 9606
-CUST NO.
-REV. LEVEL
-</code>
-linear encoder
-<code>
-RSK
-Type MSA6703
-Nr.034-042815 01003 Spec.939
-F08 Int. 10 um RI-Code02U +5V
-</code>
-====== Disposition Services microscope stand ======
-XY stepper motors and a reasonably heavy duty (not as heavy duty as the Zygo) manual Z axis.
-I believe this was from a K2 IND, or at least something very similar.  The XY stage (and maybe z too) footprint is compatible with the disposition services unit
-At the time I didn't have a use for it but bought it on speculation since it was pretty inexpensive (about $120 total IIRC)
-{{:mcmaster:tech_inst:k2_ind:xy_step_overview.jpg?300|}}
-===== Z axis and stand =====
-Currently unused, in storage
-====== Misc ======
-{{:mcmaster:tech_inst:k2_ind:k2_inds.jpg?300|}}
-Above: standard K2 IND next to the KMS310RT
-{{:mcmaster:tech_inst:k2_ind:k2_tables.jpg?300|}}
-Above: both Disposition Services stages during the swap.  The servo system baseplate is 3.5" thick (!) and the stepper system is "only" 1.9" thick.
-====== References ======
-  * [[http://siliconpr0n.org/media/tech_inst/k2_ind/tech_inst_k2_ind_manual.pdf|K2 IND manual]]
-  * [[http://siliconpr0n.org/media/tech_inst/kms_300/tech_inst_kms_300_users_guide_appendix_a.pdf|KMS 300 user guide appendix A]]: calibration procedures
-    * The only documentation that came with it...where did the rest go...
-  * [[http://siliconpr0n.org/media/zygo/kms310/KMS-310-400_Operator.pdf|Zygo KMS-310/400 Operator's Manual]]
-  * [[http://siliconpr0n.org/media/zygo/kms310/KMS-310-400_Supervisor.pdf|Zygo KMS-310/400 Supervisor's Manual]]